Model Airplane Club, California, USA
Model Airplane Club, California, USA
Home

Tanks for G-MOT and Gasparin Engines
All have M5 x .05 mm female thread
Volume
CC
Diameter
Inch
Length
Inch
Weight
Ounces
Price $
1.2 - A     0.458 0.84 0.042     $ 10.00
2 - A 0.458 1.155 0.080 $ 8.00
3 - A 0.575 1.185 0.149 $ 8.00
3 - A       0.458 1.540 0.080     $ 10.00
5 - B 0.612 1.554 0.183 $ 7.00
6 - A 0.612 1.810 0.219 $ 7.00
6 - A     0.827 1.220 0.095     $ 17.00
8 - B 0.735 1.740 0.297 $ 7.00
8.5 - A    0.827 1.72 0.20     $ 26.00
12 - A     0.827 2.2 0.24     $ 31.00
13 - B 0.968 1.793 0.497 $ 12.00
16 - B 0.968 2.10 0.547 $ 15.00
16 - A     0.827 2.68 0.30     $ 32.00
20 - A     0.827 3.20 0.329     $ 33.00
25 - B 0.968 3.035 0.733 $ 18.00
25 - A     0.827 3.83 0.415     $ 33.00
30 - A     0.827 4.475 0.429     $ 34.00
40 - A     0.827 5.75 0.600     $ 35.00
Tanks with "A" after capacity require 3mm dia. by 1.0 mm thick "O" Ring, Gasparin's standard.
Tanks with "B" after capacity require 2.6mm dia. by 1.2 thick "O" Ring, G-Mot's standard.
New for 2003! Space age aluminum: 71,116 pounds per square inch minimum tensile strength. These are about 50% lighter than prior tanks.
"O" Rings @50c, Brass Tank Lids@ $4.50
Annealed S.S. tubes are $10.00 each, sizes below:
0.5mm x 60mm - 0.6mm x 75mm
0.8 mm x 160mm - 1.2mm x 240mm

ALL TUBES IN STOCK - ALL AGAIN AVAILABLE

In late 2004 G-Mot modified their fill nozzle. This is the best filler now available, cost $30.00.
Gasparin's small engines, the G-3 through and inclusive of the G-24 Twin, have the check valve on the filler inside the tank.
This tank opening has M4 x .035 thread.

We now have a complete assembly to replace this entire filler, tube, tank connection, and inside check valve. These are $18.00 each, a duplicate of the original.
Or, for these G-3 through G-24 twins, if you wish to use the much better - new - G-Mot filler.
We offer:

  • (1) Set, M4 x .035 brass male tank lid with "O" ring, pre drilled. Cost for this set is $10.00.

    • Gasparin's G-28 and G-28RV use a 3cc tank with M3.5 x .035 thread.

    Most often this 3cc tank results in a very long engine run, with the sad results of a lost model.

    All our Gasparin and G-Mot tanks, when sold separately, have a M5 x .05 thread.

    We now have a bushing from M5 x .05 to M3.5 x .035. This make it possible to down size the 3 cc tank on the G-28 or G-28RV to 2cc or 1.2cc, without soldering.

    These bushings are $10.00 each. The "O" Ring required is $5.00.

    24 hour message machine:
    (818 ) 718-1685
    OR WRITE
    Roy E. Hanson Jr.
    21410 Nashville Street
    Chatsworth, CA 91311

    Home